Altec Industries, Inc.: Incorrect Bolt Installed
An incorrect bolt in the derrick rotation bearing may cause the adjacent bolts to be overloaded during operation, which could cause separation of the rotation bearing, and increase the risk of an injury.
Read the official notice →- Date
- 2023-01-12
- Country
- United States
- Brand
- Altec Industries
- Product
- STRUCTURE
- Units
- 45 affected
- Category
- Vehicles
- Source
- NHTSA
Copied automatically from the US National Highway Traffic Safety Administration. Details may be shortened or out of date; the official notice is the authoritative source. Disclaimer
What to do
- Check whether your vehicle is affected by entering its VIN (vehicle identification number) on the manufacturer's or the agency's recall lookup.
- Contact a dealer to book the repair. Recall repairs are normally free of charge.
- If the notice says not to drive or to park outside, follow that until the repair is done.
General guidance from Recall Atlas. The official notice from the US National Highway Traffic Safety Administration has the exact models, batch codes and remedy, and it takes priority.
More Altec Industries recalls
- 2023-05-11
USAltec Industries, Inc.: Boom Pressure Limiter Incorrectly Set
Lifting loads above the boom capacity could overload the unit and cause instability, increasing the risk of injury.
- 2023-05-04
- US
Altec Industries, Inc.: Auger Extension Assembly Missing Hardware
An auger extension bar that detaches while the digger drive unit is deployed, can increase the risk of injury to nearby personnel.
- 2023-03-30
- US
Altec Industries, Inc.: Missing Weld On Rear Pole Rack
A missing weld on the rear pole rack can lead to a crack that could cause the pole and rack to drop in height, increasing the risk of an injury.
- 2022-10-21
- US
Altec Industries, Inc.: Jib Winch May be Operated without Outriggers Set
Outriggers that are not set when loads are being lifted by the jib winch may cause the unit to tip, increasing the risk of injury.
- 2022-08-10
- US
Altec Industries, Inc.: Boom Weld May Crack
A cracked weld may allow the auger bracket to detach from the boom, increasing the risk of injury.
- 2022-08-04
- US
Altec Industries, Inc.: Engine Stall from Blown Ignition Circuit Fuse
A blown fuse can cause an engine stall, increasing the risk of a crash.
Other vehicles recalls in the United States
- 2023-01-13
- US
Forest River, Inc.: Incorrect Seating Information on Label/FMVSS 120
Incorrect belted seating position information may result in unbelted passengers, increasing the risk of injury in a crash.
- US
Comoto Holdings, Inc.: Helmets May Not Adequately Protect User/FMVSS 218
A helmet that does not provide adequate protection increases the risk of injury during a crash.
- US
Comoto Holdings, Inc.: Helmets May Not Adequately Protect User/FMVSS 218
A helmet that does not provide adequate protection increases the risk of injury during a crash.
- 2023-01-12
- US
American Honda Expands Recall of Honda Talon 1000 ROVs Due to Crash and Injury Hazards
The vehicle's intake funnel band screw can loosen and enter the engine through the intake funnel and cause sudden engine failure. If this occurs, it can result in a loss of control, increasing the risk of a crash or…
CPSCAmerican Honda Motor Co. Inc., of Torrance, CaliforniaAbout 34,000 (About 32,000 were previously recalled in…Official notice → - 2023-01-06
- US
Triple E Recreational Vehicles: Battery Disconnect Switch May Short
An electrical short-circuit can increase the risk of a fire.
- 2023-01-05
- US
Volvo Car USA, LLC: Steering Wheel May Lock Up
A screw inside the gearbox housing can cause the steering wheel to lock up and increase the risk of a crash.